Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Margate, FL
Chimney work in Margate, FL rarely starts with a dirty flue. It usually starts with a rusted metal cap, corroded flashing, or a prefabricated chimney that has spent one too many summers in salty, humid air. Most Margate homes are single-story concrete-block ranch houses built between the 1960s and 1980s, and the majority have prefabricated metal chimney systems rather than full masonry fireplaces. That changes what a chimney company here actually does. Ashby Chimney Fort Lauderdale works on those prefab systems every week: we inspect for rust, replace damaged caps, and make sure the whole assembly vents combustion gases safely, even when the fireplace only gets used a few times a year. Call (754) 354-1451 for honest answers about your setup.
Why Margate Homes Are Different
Margate sits close enough to the Atlantic that sea breezes carry salt inland, and the subtropical humidity does the rest. A fireplace that sat unused from March to December still corrodes. Metal chimney caps pit and rust, flashing pulls away from the roofline, and galvanized components that look fine from the ground turn out to be paper-thin up close. The most common call we get in Margate is not for soot buildup. It is for a rusted-out cap or corroded flashing after a long, wet summer.
The housing stock compounds it. Most homes in Margate were built as concrete-block ranches, and the fireplaces in them are almost always factory-built prefab units. Those systems use thin metal flue liners that do not tolerate salt air the way a full masonry chimney in an older city might. When a prefab liner rusts through, combustion gases can leak into the wall cavity, and that is a carbon monoxide risk you cannot see or smell. Even decorative fireplaces, common in 1970s and 1980s Margate homes, need the venting checked because a decorative fire still produces gases that must leave the house.
Margate has no hills and no freeze-thaw cycles, so the problems here are different from what a chimney company sees up north. We are not chasing cracked brick from ice. We are chasing rust, corrosion, and water intrusion at the cap and flashing points. The good news: these are discoverable problems. A camera inspection shows exactly what is happening inside the flue, and you can see the images yourself before you spend a dollar on repairs.
Styles & brands we work with
Our Main Margate Services
Margate homeowners call us most often for two things: a sweep when the fireplace has not been cleaned in years, and an inspection when they see rust or staining near the chimney chase or roofline. We also repair what those inspections find.
Chimney Sweep in Margate
A chimney sweep here is less about heavy creosote and more about clearing debris, checking for rust, and confirming the cap and liner are still doing their jobs. In Margate, birds and wasps nest in unused flues during the long off-season, and the remains block airflow. We remove that debris, brush what needs brushing, and let you know if the metal components show corrosion that needs attention before you burn again. If you have not had yours looked at in years, start with a Chimney Sweep in Margate.
Chimney Inspection in Margate
Inspection matters more in Margate than in drier climates, because rust works quietly. We run a camera through the flue and show you the feed. You will see whether the liner is intact, whether the cap is solid, and whether the flashing still seals. The most common finding in Margate is a prefab metal liner starting to pit. Some pitting is cosmetic, and some is structurally important, and the camera images are what let us tell the difference honestly. Book a Chimney Inspection in Margate before burning season, not after the season’s first fire reveals a problem.
Fireplace Repair in Margate
When an inspection finds a rusted cap, a corroded chase top, or a damaged liner, the repair path is usually straightforward. We quote a written price before any work starts, and the parts we use come from brands built for chimney systems, not whatever is cheap at the hardware store. Most Margate fireplace repairs involve replacing metal components: caps, flashings, chase covers, and occasionally liner sections. The salt air means we recommend stainless or coated options where possible, because they hold up longer here. See what is involved at Fireplace Repair in Margate.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Margate
Most Margate prefab fireplaces and factory-built chimneys use components from a handful of common manufacturers, and we service all of them. We stock and install parts from Copperfield, DuraFlex, and HeatShield, and when a repair calls for a Gelco cap or chase cover, we order it immediately. See our brands for the full picture of what we carry and why we chose these lines.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Margate, FL
| Service | Typical range in Margate |
|---|---|
| Standard chimney sweep | $169 – $259 |
| Chimney sweep with camera inspection | $219 – $315 |
| Level 1 chimney inspection | $129 – $219 |
| Level 2 camera inspection | $259 – $399 |
| Chimney cap replacement | $190 – $340 |
| Chase cover replacement | $230 – $410 |
| Prefab flue liner repair | $450 – $950 |
| Flashing repair or reseal | $190 – $360 |
| Dryer vent cleaning | $129 – $219 |
What pushes a Margate job toward the upper end: heavy rust on the cap and flashing, a liner that needs more than a small patch, or a prefab system that has been leaking long enough to damage surrounding framing. What does not push the price up is the quote itself. Every job gets a written price before work begins, and the number on the invoice matches the number at the door. No exceptions.
Neighborhoods We Serve in Margate
We work throughout Margate, from the established ranch neighborhoods around Margate Boulevard and Atlantic Boulevard to the quieter streets near Winfield Boulevard and Rock Island Road. Most jobs can be scheduled within a few days, with tighter windows available as burning season approaches.
- Margate Estates
- Club House Estates
- Carolina
- Palm Springs
- Oriole Gardens
Service Area – Cities Near Margate
Chimney work in this part of Broward County has predictable patterns: same salt air, same prefab metal systems, same off-season rust. We run appointments into Pompano Beach, FL, Plantation, FL, Fort Lauderdale, FL, and Hollywood, FL for homeowners who want the same written-price, written-guarantee approach we bring to Margate.
Serving Margate, FL - Our Local Coverage Area
We’re based in the Margate area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Margate
Most Margate jobs are scheduled within three to five business days. During the weeks before burning season, the schedule tightens, so if you want a sweep and inspection before your first fire, call early. The phone is answered by a live person, 24/7, so you will not sit in a voicemail loop.
Most routine sweeps and inspections do not require a permit. Repairs that stay within the existing chimney footprint, like a cap replacement, flashing reseal, or liner patch, typically do not either. If your job does require one, we will tell you clearly before any work is scheduled.
Some Margate HOAs have rules about visible roof penetrations and cap styles, especially in communities with a unified aesthetic. If your association has requirements, we work within them, and we will note any cap-type restrictions before we recommend a replacement. The cleaning itself is rarely affected by HOA rules; it is the visible hardware that matters.
If you are in Margate and the fireplace has not been checked in a few seasons, call (754) 354-1451. We will give you a written price, show you the camera feed, and tell you straight if the chimney can wait or needs work now. The estimate is free, and so is the honesty.
What happens when you call
- 1A real person answersNo phone trees - talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Margate Customers Say
"Annual cleaning. Drop cloth down, vacuum running, hearth spotless after. No pressure to buy a cap or anything extra. Just did what I booked and charged the quote."
- Keith Donovan"No upsell nonsense. I expected him to tell me I needed a thousand dollars of work. He said the firebox was fine, swept it, and charged me the quote. That kind of honesty gets my repeat business."
- Steve Karras"Had them out for the yearly sweep before we start burning. He put down a drop cloth, swept it clean, and actually showed me the inside of the flue on a little camera. No mess, no surprises on the bill."
- Bill Prentice