Famco Chimney Inspection Nationwide

Famco Chimney Inspection in Fort Lauderdale: What to Know First

We provide independent Famco chimney inspection in Fort Lauderdale, typically completed within 90 minutes for a standard Level 2 inspection, with a written report and camera footage you can see for yourself before you decide on any repairs. Most inspections run between $189 and $349 depending on the level and access, and we hand you the price before we touch a single tool. If you own a Famco fireplace, chimney cap, or damper system and want an honest read on its condition, call (754) 354-1451 and we’ll walk you through what to expect.

Call (754) 354-1451

This page is for Fort Lauderdale homeowners who have Famco equipment and want to know what actually happens during an inspection, what we see on Famco products in this climate, and what it costs to keep things safe. No scare tactics, no mystery pricing. We’ll tell you straight.

How Famco Products Fail – and How We Fix Them

Famco builds solid equipment, but Fort Lauderdale’s salt air and humidity create a specific set of problems we see over and over. Here’s what we find on Famco jobs in this area.

• Famco chimney caps: rust at the mounting flange. We regularly inspect Famco’s stainless and galvanized caps in Fort Lauderdale and the weak point is almost always the mounting flange where the cap meets the flue tile. Salt-laden air settles there, condensation sits, and the flange corrodes years before the cap body. We check for pinholes and pulled screws, then replace with the correct Famco-size cap or a quality aftermarket equivalent if the flue tile is non-standard.
• Famco dampers: stuck or seized pivot pins. The pivot pins on Famco throat dampers seize up in high-humidity homes, especially along the Intracoastal corridors. The damper won’t fully open or close, which affects draft and lets conditioned air escape. We free the mechanism during inspection when safe, but if the pin is corroded through, we recommend replacement and show you the camera evidence.
• Famco multi-flue caps: hidden rust under the lid. Famco’s multi-flue caps hold up well on top, but the underside of the lid is where we find trouble. Condensation trapped under the lid in Fort Lauderdale’s humid months rusts the seams from the inside out. You can’t see it from the ground. Our camera inspection catches it early.
• Famco spark arrestors: mesh clogged with salt and soot. The fine mesh on Famco spark arrestors catches more than sparks. Over two or three years in Fort Lauderdale, we see the mesh packed with a mix of creosote, salt residue, and wind-blown sand from the barrier island. A clogged arrestor restricts draft and pushes smoke back into the house. The fix is often a deep cleaning, not a replacement, but we’ll show you the before and after on camera.
• Famco chase covers: corrosion at the corners. On prefab fireplace installations, Famco chase covers take the full brunt of Florida’s afternoon downpours and salt spray. The corners fail first because that’s where water pools and sits. We inspect for perforation with a bright light and mirror, and when we find it, we quote a replacement with proper slope so water runs off instead of collecting.

Our Famco Chimney Inspection Process

Here’s how a Famco inspection works at Ashby Chimney Fort Lauderdale, from the first call to the final report. Nathan Corliss built this process so there are no surprises at any point.

1. 1
   Call and scheduling. A live person answers, day or night. You tell us what Famco equipment you have, and we give you a written price range for the inspection level you need before we book anything.
2. 2
   Arrival and setup. Our technician arrives in uniform, introduces himself, and confirms the scope of work in writing. No price changes at the door.
3. 3
   Level 1 or Level 2 assessment. We inspect the accessible portions of the fireplace, flue, damper, and Famco components. For a Level 2, we run a camera through the entire flue and document every seam, joint, and transition.
4. 4
   Camera documentation. You see the footage on our screen before we leave. If we find a problem, you see it with your own eyes, not just our word.
5. 5
   Written findings and price. We write up exactly what we found, what needs attention, and what can safely wait. Every repair recommendation comes with a written price, and we tell you plainly if something is cosmetic versus a safety issue.
6. 6
   Repair or report. If you authorize a repair, we do it with the correct parts for your Famco unit. If not, you keep the report and photos. Either way, the guarantee comes in writing.

What Famco Chimney Inspection Costs in Fort Lauderdale

Most Famco chimney inspections in Fort Lauderdale run between $189 and $349. A Level 1 visual inspection, where we check the accessible parts of the fireplace and damper, usually lands around $189 to $229. A Level 2 camera inspection, which includes full video documentation of the flue interior, typically runs $279 to $349. If the chimney requires roof access with steep pitches or complex chase assemblies, the price can move up a bit from there.

What shifts the price is access difficulty, the height of the chase, and whether we need to remove a Famco cap or damper assembly to get the camera through. We quote the exact number before we start, and that number doesn’t change. Call (754) 354-1451 for a free estimate.

Why Fort Lauderdale Homeowners Call Ashby Chimney Fort Lauderdale for Famco Work

We’ve been inspecting and repairing chimneys since 2002, and our techs know Famco products well enough to spot the failure modes other contractors miss. When a Famco component needs replacement, we use quality parts sourced from trusted chimney-trade suppliers, including DuraFlex, HeatShield, and Gelco, and we match the correct Famco-sized part to your flue rather than adapting something that sort of fits. Our 365-Day Done Right Promise means if a repair we make fails within the guarantee period, we return and fix it at no charge. Every job gets a written price before work starts and a written guarantee when it’s done. Say the price first, explain the work second, put it all in writing – that is the whole business model.

FAQs